www.elektronik.si :: Poglej temo

www.elektronik.si Bluetooth ZS-040

www.elektronik.si -> Komponente in podsklopi

Avtor: Silvo, Kraj: Koroška-okolica Dravograda

Objavljeno: Ned Maj 20, 2018 11:37 am Naslov sporočila: Bluetooth ZS-040
----------------------------------------------------------------------------
Imam zgoraj omenjen bluetooth -> RS232 modulček. (Cipset CC2541) Koliko sem uspel najti gre dejansko za klona HM10.
Zadeva s strani RS232 deluje - se odziva na AT ukaze. Z strani BT pa je "mrtva" . Ni vidna na nobeni napravi. (preizkušeno na več različnih telefonih) Poskusil sem dva komada. Nobeden ne deluje. Rdec led utripa v ritmu ca 1.sec.
Mogoče kdo ve kje je problem? So modulčki zanič? Imam enega starejšega(mislim, daje HC06), ki pa dela brez problema.

Nabor ukazov, ki jih vrača AT+HELP

Koda:

********************************************************************
* Command Description          *
* ---------------------------------------------------------------- *
* AT Check if the command terminal work normally *
* AT+RESET Software reboot             *
* AT+VERSION Get firmware, bluetooth, HCI and LMP version *
* AT+HELP List all the commands       *
* AT+NAME Get/Set local device name *
* AT+PIN Get/Set pin code for pairing *
* AT+PASS Get/Set pin code for pairing *
* AT+BAUD Get/Set baud rate       *
* AT+LADDR Get local bluetooth address       *
* AT+ADDR Get local bluetooth address       *
* AT+DEFAULT Restore factory default          *
* AT+RENEW Restore factory default          *
* AT+STATE Get current state             *
* AT+PWRM Get/Set power on mode(low power)       *
* AT+POWE Get/Set RF transmit power       *
* AT+SLEEP Sleep mode       *
* AT+ROLE Get/Set current role.    *
* AT+PARI Get/Set UART parity bit. *
* AT+STOP Get/Set UART stop bit. *
* AT+START System start working.          *
* AT+IMME System wait for command when power on.    *
* AT+IBEA Switch iBeacon mode.    *
* AT+IBE0 Set iBeacon UUID 0.    *
* AT+IBE1 Set iBeacon UUID 1.    *
* AT+IBE2 Set iBeacon UUID 2.    *
* AT+IBE3 Set iBeacon UUID 3.    *
* AT+MARJ Set iBeacon MARJ .    *
* AT+MINO Set iBeacon MINO .    *
* AT+MEA Set iBeacon MEA .    *
* AT+NOTI Notify connection event . *
* AT+UUID Get/Set system SERVER_UUID .    *
* AT+CHAR Get/Set system CHAR_UUID .    *
* -----------------------------------------------------------------*
* Note: (M) = The command support slave mode only.       *
* For more information, please visit http://www.bolutek.com *
* Copyright@2013 www.bolutek.com. All rights reserved.       *
********************************************************************
+VERSION=Firmware V3.0.6,Bluetooth V4.0 LE
+NAME=CC41-A

PS
EN pin naj ne bi bilo potrebno priklopit nikamor. Sem ga sicer poskusil na visoko in nizko stanje a ni sprermemb.

Avtor: Vlado, Kraj: Ljubljana

Objavljeno: Ned Maj 20, 2018 6:18 pm Naslov sporočila:
----------------------------------------------------------------------------
Silvo,
poskusi postopek na tej strani:

http://fab.cba.mit.edu/classes/863.15/doc/tutorials/programming/ble_duplex.html

Stran 1 od 1