www.elektronik.si :: Poglej temo - [3Dp] STL editor, urejevalnik, zloževalnik

www.elektronik.si
Forum o elektrotehniki in računalništvu

Pomoč

Išči

Seznam članov

Skupine

Statistika

Album

Filemanager

DocDB

Povezave

Registriraj se

Pravila

Bolha

Priponke

Koledar

Zapiski

Tvoj profil

Prijava za pregled zasebnih sporočil

Prijava

[3Dp] STL editor, urejevalnik, zloževalnik
Pojdi na stran Prejšnja 1, 2

www.elektronik.si Seznam forumov -> 3D Tiskanje

Poglej prejšnjo temo :: Poglej naslednjo temo

Avtor

Sporočilo

besoft
Član
Član

Pridružen-a: Ned 01 Apr 2012 10:22
Prispevkov: 585
Aktiv.: 3.64
Kraj: Žižki - Prekmurje

Objavljeno: Pet Apr 25, 2014 4:48 pm Naslov sporočila:

Saj se prime, vendar se suport odlomi ali odreže.

Nazaj na vrh

damirk
Član
Član

Pridružen-a: Čet 12 Jul 2012 12:39
Prispevkov: 20
Aktiv.: 0.13
Kraj: Maribor

Objavljeno: Sre Maj 07, 2014 1:57 pm Naslov sporočila:

Kroko je napisal/a:

Imam STL datoteko ki bi jo rad natisnil. Problem je, ker je v model v bistvu samo "plašč", za tiskanje pa bi potreboval tudi notranjost.

Mogoče kdo ve kako bi to naredil?

Rešitev je Water Soluble filament s katerim natisneš še notranjost - po tiskanju pa ga namočiš v vodo in notranjost se raztopi...

Citiram:

If your 3D printer has a dual extruder, you can print with ABS/PLA and PVA to build structures which are impossible to make without support material. When your print is done just give it a nice bath in cold/warm water, let the PVA dissolve resulting in a seemingly “impossible” creation made with a FFF/FDM desktop 3D printer. Imagine which complex structures you are now able to print….. Extremely difficult to print models, which were previously only printable with very expensive SLS printers, become available to FFF/FDM 3D printers by making use of a soluble support material like PVA! Think about mechanical applications – such as ball bearings, ball and socket joints, and caged gear mechanisms – which are now available for printing with FFF/FDM 3D printers. Also think about applications, such as being able to make water soluble moulds.

http://www.formfutura.com/175mm-water-soluble-filament-pva.html
http://www.makerbot.com/blog/2011/02/21/makerbot-introduces-water-soluble-3d-printer-filament/

Nazaj na vrh

Pokaži sporočila:

	www.elektronik.si Seznam forumov -> 3D Tiskanje	Časovni pas GMT + 2 uri, srednjeevropski - poletni čas Pojdi na stran Prejšnja 1, 2
Stran 2 od 2

Pojdi na:

Ne, ne moreš dodajati novih tem v tem forumu
Ne, ne moreš odgovarjati na teme v tem forumu
Ne, ne moreš urejati svojih prispevkov v tem forumu
Ne, ne moreš brisati svojih prispevkov v tem forumu
Ne ne moreš glasovati v anketi v tem forumu
Ne, ne moreš pripeti datotek v tem forumu
Ne, ne moreš povleči datotek v tem forumu

Uptime: 493 dni